Vectronics VEC-1402K Manual de usuario descargar pdf

IMPORTANT WARRANTY INFORMATION! PLEASE READ

Return Policy on Kits When Not Purchased Directly From Vectronics: Before continuing

any further with your VEC kit check with your Dealer about their return policy. If your Dealer

allows returns, your kit must be returned before you begin construction.

Return Policy on Kits When Purchased Directly From Vectronics: Your VEC kit may be

returned to the factory in its pre-assembled condition only. The reason for this stipulation is,

once you begin installing and soldering parts, you essentially take over the role of the device's

manufacturer. From this point on, neither Vectronics nor its dealers can reasonably be held

accountable for the quality or the outcome of your work. Because of this, Vectronics cannot

accept return of any kit-in-progress or completed work as a warranty item for any reason

whatsoever. If you are a new or inexperienced kit builder, we urge you to read the manual

carefully and determine whether or not you're ready to take on the job. If you wish to change

your mind and return your kit, you may--but you must do it before you begin construction, and

within ten (10) working days of the time it arrives.

Vectronics Warrants: Your kit contains each item specified in the parts list.

Missing Parts: If you determine, during your pre-construction inventory, that any part is

missing, please contact Vectronics and we'll send the missing item to you free of charge.

However, before you contact Vectronics, please look carefully to confirm you haven't misread

the marking on one of the other items provided with the kit. Also, make certain an alternative

part hasn't been substituted for the item you're missing. If a specific part is no longer

available, or if Engineering has determined that an alternative component is more suitable,

Vectronics reserves the right to make substitutions at any time. In most cases, these changes

will be clearly noted in an addendum to the manual.

Defective Parts: Today's electronic parts are physically and electrically resilient, and

defective components are rare. However, if you discover an item during your pre-construction

inventory that's obviously broken or unserviceable, we'll replace it. Just return the part to

Vectronics at the address below accompanied with an explanation. Upon receipt, we'll test it.

If it's defective and appears unused, we'll ship you a new one right away at no charge.

Missing or Defective Parts After You Begin Assembly: Parts and materials lost or

damaged after construction begins are not covered under the terms of this warranty. However,

most parts supplied with VEC kits are relatively inexpensive and Vectronics can replace them

for a reasonable charge. Simply contact the factory with a complete description. We'll

process your order quickly and get you back on track.

Factory Repair After You Begin Assembly: Kits-in progress and completed kits are

specifically excluded from coverage by the Vectronics warranty. However, as a service to

customers, technicians are available to evaluate and repair malfunctioning kits for a minimum

service fee of $18.00 (½ hour rate) plus $7.00 shipping and handling (prices subject to

change). To qualify for repair service, your kit must be fully completed, unmodified, and the

printed circuit board assembled using rosin-core solder. In the event your repair will require

more than an hour to fix (or $36.00, subject to change), our technicians will contact you in

advance by telephone before performing the work. Defective units should be shipped prepaid

to:

Vectronics

1007 HWY 25 South

Starkville, MS 39759

1 2 3 4 5 6 ... 18 19

Indice de contenidos

Pagina 1

IMPORTANT WARRANTY INFORMATION! PLEASE READ Return Policy on Kits When Not Purchased Directly From Vectronics: Before continuing any further with yo

Pagina 2

VEC-1402K Instruction Manual 2 Meter Pre-Amp Kit 8 STEP-BY-STEP ASSEMBLY Before assembling your kit, please take time to read and understand the VEC

Pagina 3 - TABLE OF CONTENTS

VEC-1402K Instruction Manual 2 Meter Pre-Amp Kit 9 ! ! 2. Install and solder C1, making sure the capacitor remains firmly seated during installati

Pagina 4 - BEFORE YOU START BUILDING

VEC-1402K Instruction Manual 2 Meter Pre-Amp Kit 10 the bottom of the board, fold both tabs over onto the foil, securing the shield can in place. So

Pagina 5

VEC-1402K Instruction Manual 2 Meter Pre-Amp Kit 11 PC Board Inspection: Before applying power to your kit, give it a thorough QC (quality control) i

Pagina 6 - Resistor Color Code

VEC-1402K Instruction Manual 2 Meter Pre-Amp Kit 12 Now that your inspection is completed, you're ready to begin the testing and alignment phas

Pagina 7

VEC-1402K Instruction Manual 2 Meter Pre-Amp Kit 13 Off-air Method: Set your preamp and receiver up, as described above, using an antenna in place o

Pagina 8

VEC-1402K Instruction Manual 2 Meter Pre-Amp Kit 14 signals. Many scanner listeners use 100 feet or more of poor-grade RG-58 or TV-type coax between

Pagina 9

VEC-1402K Instruction Manual 2 Meter Pre-Amp Kit 15 IN CASE OF DIFFICULTY Preamp Stops Amplifying: A working preamp that fails "in-service"

Pagina 10 - STEP-BY-STEP ASSEMBLY

VEC-1402K Instruction Manual 2 Meter Pre-Amp Kit 16 THEORY OF OPERATION AND SPECIFICATIONS Operation: Coil L1 and capacitors C1 and C2 combine to for

Pagina 11

Pagina 12 - Important Note:

When shipping, pack your kit well and include the minimum payment plus shipping and handling charges ($25.00 total). No work can be performed without

Pagina 13

TABLE OF CONTENTS Introduction...2 Tools and Suppl

Pagina 14 - TESTING AND ALIGNMENT

VEC-1402K Instruction Manual 2 Meter Pre-Amp Kit 2 INTRODUCTION Now you can soup-up your 2-meter receiver or scanner with a 16-dB boost. The VEC-140

Pagina 15 - OPERATING INSTRUCTIONS

VEC-1402K Instruction Manual 2 Meter Pre-Amp Kit 3 Experience shows there are four common mistakes builders make. Avoid these, and your kit will pro

Pagina 16

VEC-1402K Instruction Manual 2 Meter Pre-Amp Kit 4 If you make a mistake and need to remove a part, follow these instructions carefully! First, gras

Pagina 17 - IN CASE OF DIFFICULTY

VEC-1402K Instruction Manual 2 Meter Pre-Amp Kit 5 on during construction. Some builders find it especially helpful to arrange resistors in ascendin

Pagina 18

VEC-1402K Instruction Manual 2 Meter Pre-Amp Kit 6 Transistors: If transistors are installed incorrectly, damage may result when power is applied. T

Pagina 19

Modelos relacionados VEC-1422K | VEC-1444K |

Comentarios a estos manuales

Sin comentarios

Vectronics VEC-1402K Manual de usuario

Busca en linea o descarga Manual de usuario para Receptores y amplificadores Vectronics VEC-1402K. Vectronics VEC-1402K User Manual Manual de usuario

Indice de contenidos

Modelos relacionados VEC-1422K | VEC-1444K |

Comentarios a estos manuales

Relacionado con productos y manuales para Receptores y amplificadores Vectronics VEC-1402K